Calculadoras de obra
English

Calculadora de ladrillo delgado

3429 ladrillos delgados6.86 por SF · planas
Área del muro
500.00 SF
Planas
3,429 planas (6.86 por SF)
Adhesivo (60 SF por bulto)
9 bultos
Mortero para juntear (50 SF por bulto)
10 bultos
Junta a rellenar
3.81 ft³
Limpiador
2 gal (1 × 5 gal)

Estos croquis son para ayudarte a pedir material y cotizar el trabajo rápido. No son planos de ingeniería ni de taller — construye siempre con los planos aprobados del proyecto.

Medida del ladrillo
Junta de mortero
Cómo se instala

El rendimiento por bulto depende del producto — los valores son de la guía de Old Mill (adhesivo de 50 lb ≈ 60 SF, mortero de 80 lb ≈ 50 SF). Escribe 0 para no contarlo.

Limpiador de ladrillo▾
Envase
Ajustes▾
Ver las cuentas▾
  1. Ladrillos por SF
    144 ÷ ((length + joint) × (height + joint)), in inches
    144 ÷ ((7.625 + 0.375) × (2.25 + 0.375)) = 6.857
  2. Planas
    wall SF × bricks per SF, rounded up
    500 SF × 6.857 = 3,429
  3. Adhesivo
    wall SF ÷ SF per unit, rounded up
    500 ÷ 60 = 9
  4. Junta a rellenar
    bricks per SF × (cell − brick face) × joint depth × wall SF
    6.857 × 3.844 in² × 0.5 in × 500 SF = 3.81 ft³
  5. Mortero para juntear
    wall SF ÷ SF per bag, rounded up
    500 ÷ 50 = 10
  6. Limpiador
    wall SF ÷ SF per gallon, rounded up
    500 ÷ 300 = 2

De dónde salen los números

  • Bricks per SF: 144 ÷ ((L + joint) × (H + joint)); modular 2¼" × 7⅝" with a ⅜" joint = 144 ÷ (8 × 2⅝) = 6.86 per SFPure geometry. Glen-Gery lists its modular thin brick (2¼" × 7⅝" face, 9/16" thick) at 6.86 per SF, the same as this math. Norman 2¼" × 11⅝" = 4.57, utility 3⅝" × 11⅝" = 3.00 with a ⅜" joint. Thin brick faces match the full-size brick faces in BIA Technical Note 10.Fuente
  • Corner pieces: One per course: 12 ÷ (H + joint) per LF of outside corner; modular with ⅜" = 4.57 per LFPure geometry — one L-shaped corner per course. Flats are figured on the full wall SF and not reduced for the corners, so the flat count runs slightly high. Makers sell corners by the box (count per LF varies, about 4.5–5 for modular) — check yours.
  • Panels and screws: Glen-Gery Thin Tech: 48" × 48" panels (wall SF ÷ 16); 24 fasteners per panel (at least 1 per SF); support ties at 2-11/16" for 2¼" brick (3 courses = 8"), so modular is 144 ÷ (8 × 8/3) = 6.75 flats per SF and 12 ÷ 8/3 = 4.5 corners per LFThin Tech installation manual (6/2020): Table 1 (panel sizes and tie spacing), the estimating notes ("divide by 16 for the number of support panels"; "24 fasteners recommended… multiply number of panels by 24") and Table 3 (modular 6.75 per SF, 4.5 per LF). The holes sit on a 16" × 8" pattern but the edge rows double up, so 24 per panel (1.5 per SF); the grid option (SF × 144 ÷ h × v) is there for other systems. The manual adds at least 2% waste for panels; the page leaves waste at 0 unless you enter it.Fuente
  • Adhesive: Old Mill: 50 lb of thin-set covers about 60 SF with a ⅜" notch trowelCoverage depends on the product, the trowel notch and the back of the brick — use the number on your adhesive's data sheet.Fuente
  • Pointing mortar: Old Mill: an 80 lb bag of type S mortar or sanded grout covers about 50 SFThe joint volume (bricks per SF × joint face per brick × joint depth) is shown for reference: modular with a ⅜" joint filled ½" deep is about 13.2 in³ per SF. Bag yield depends on the mix and how much is lost from the grout bag.Fuente
  • Brick wash: PROSOCO Sure Klean 600: 300–1,200 SF per gallon of concentrate (we use 300 so it isn't short)Coverage per gallon of concentrate varies with the brick's texture and porosity; the data sheet lists it by substrate. Test a small area first and follow the maker's dilution.Fuente

Resultados guardados

Nada guardado todavía. Toca Guardar para conservar un resultado en este dispositivo.

Todo para un muro de ladrillo delgado según sus SF: planas, esquineros, paneles y tornillos, adhesivo, mortero para juntear y limpiador.